in modern 6 0 mpa steam pressure boiler the desired ph value of feed water is

Product thermal capacity: 4-35 t/h
Working pressure: 1.0-2.5 MPA
Outlet temperature:: 184-350 ℃
Available fuel: Bituminous coal, lean coal, anthracite
Available industries: Heating, chemical, food, tobacco, textile, print and dyeing, feed, medicine, building materials, wine, hospital

>Cleaver-Brooks | Reference Center | Boiler Basics | Ste

Cleaver-Brooks | Reference Center | Boiler Basics | Steam

The primary purpose of the boiler is to supply energy to the facility's operations – for comfort heating, manufacturing process, laundry, kitchen, etc. The nature of the facility's operation will dictate whether a steam or hot water boiler should be used. Hot water is commonly used in heating applications, with the boiler supplying water to the system at 120°F to 220°F.

Get A Quote

>BOILERS | Energy-Models.c

BOILERS | Energy-Models.com

Fire tube or "fire in tube" boilers; contain long steel tubes through which the hot gasses from a furnace pass and around which the water to be converted to steam circulates. (Refer Figure 2.2). Fire tube boilers, typically have a lower initial cost, are more fuel efficient and easier to operate, but they are limited generally to capacities of 25 tons/hr and pressures of 17.5 kg/cm 2.

Get A Quote

F]

Boiler – Fundamentals and Best Practic

[PDF]

Boiler – Fundamentals and Best Practices

Steam Tables Pressure psig Temperature °F Sensible Heat Btu/lb Latent Heat Btu/lb Total Heat Btu/lb the control of feedwater and boiler water chemistry in modern industrial boilers. Basic Boiler Calculations. Basic Boiler Calculations Feedwater 6 Condensate 0 10 15 0 50 Feed water 1 105 182.5 3 Basic Boiler Calculations. Boiler Water

Get A Quote

>Boiler Efficiency - an overview | ScienceDirect Topi

Boiler Efficiency - an overview | ScienceDirect Topics

The shell is heated by low-pressure (waste) steam at 0.4–0.5 MPa and at 160 °C, which condenses inside the inter-tube space. Brown coal with a particle size of less than 10 mm enters the tubes with a diameter of 100 mm on the upper side of the shell, passes through the tubes, and is …

Get A Quote

>Chapter 17 - Measurement Of Steam Purity | SU

Chapter 17 - Measurement Of Steam Purity | SUEZ

The exact ratio of sodium to dissolved solids in the boiler water and consequently in the steam can be determined for each plant but is approximately 1:3 for most plants (i.e., for each 0.1 ppm of sodium in the steam there is approximately 0.3 ppm of dissolved solids present).

Get A Quote

>Boilers test prep Flashcards | Quizl

Boilers test prep Flashcards | Quizlet

Boilers operating at a steam or other vapor pressure of 15 PSIG or less, or hot water or other liquid boiler in which the pressure does not exceed 160 PSIG or a temperature of 250 degrees f A person holding a current state Minnesota Special Engineers license could …

Get A Quote

]

Boiler water Limit:- - Altr

[PDF]

Boiler water Limit:- - Altret

This value will limit the silica content of the steam to 0.25 ppm as a function of selective. Feed Water & Boiler water Characteristics as per IS:10392-1982 1.FEED WATER Parameters Upto 20 Kg/cm2 21 Kg/cm2 to 39 Kg/cm2 40 Kg/cm2 to 59 Kg/cm2 Unit Total Hardness <10 <1.0 <0.5 ppm as CaCO 3 pH Value 8.5-9.5 8.5-9.5 8.5-9.5 Dissolved Oxygen

Get A Quote

F]

Thermodynamics I Spring 1432/1433H (2011/2012H)

[PDF]

Thermodynamics I Spring 1432/1433H (2011/2012H) …

operating pressure of the boiler . The water temperature increases somewhat during this Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 75 kPa. Determine the thermal efficiency of ηth = wnet /qin = 710.07 /2728.6 = 0.260 or 26 %

Get A Quote

>(PDF) Process condensate stripper performance in ammon

(PDF) Process condensate stripper performance in ammonia

11 0 0 0 0.30 Tabl e 8: Ef fect of steam i nlet fl ow rate on stri pping o f CO 2 , N H 3 and CH 3 OH (low pressu re strip per var iant, s tripper bottom) P = 0. 35 MPa, T = 21 5°C)

Get A Quote

>Steam Inlet Temperature - an overview | ScienceDirect Topi

Steam Inlet Temperature - an overview | ScienceDirect Topics

Example 1.6. Using Figure 1.11, calculate the ideal cycle efficiency and specific steam consumption (s.s.c.) of a reheat cycle operating between pressures 8 MPa and 9.6 kPa with a superheat temperature and reheat temperature of 773 K and 773 K, respectively.(Assume steam condition after first expansion as dry saturated and neglect work input to boiler feed pump.)

Get A Quote

>Rankine Cycle - Steam Turbine Cyc

Rankine Cycle - Steam Turbine Cycle

State 2 is fixed by the pressure p 2 = 6.0 MPa and the fact that the specific entropy is constant for the isentropic compression (s 1 = s 2 = 0.592 kJ/kgK for 0.008 MPa). For this entropy s 2 = 0.592 kJ/kgK and p 2 = 6.0 MPa we find h 2, subcooled in steam tables for compressed water (using interpolation between two states). h 2, subcooled

Get A Quote
Contact us
Tel

0086-510-68530066

Chat online

Online message


Gas-fired(oil-fired) boilers
Coal-fired boilers
Biomass-fired boilers
Thermal oil heaters
Hot water:0.7-14 MW
14.1-21 MW
21.1-29 MW
29.1-75 MW
Steam :  1-10 t/h
11-20 t/h
21-90 t/h
91-140 t/h