regenerative heating i e bleeding steam to reheat feed water to boiler

Product thermal capacity: 4-35 t/h
Working pressure: 1.0-2.5 MPA
Outlet temperature:: 184-350 ℃
Available fuel: Bituminous coal, lean coal, anthracite
Available industries: Heating, chemical, food, tobacco, textile, print and dyeing, feed, medicine, building materials, wine, hospital

>Solved: A Steam Power Plant Operates On An Ideal Regener

Solved: A Steam Power Plant Operates On An Ideal Regenerat

Question: A Steam Power Plant Operates On An Ideal Regenerative Rankine Cycle. Steam Enters The Turbine At 6 MPa And 450 C And Is Condensed In The Condenser At 20 KPa. Steam Is Extracted From The Turbineat 0.4 MPa To Heat The Feedwater In An Open Feedwater Heater. Water Leaves The Feedwater Heater As A Saturated Liquid.

Get A Quote

>Rankine Cycle and Regenerative Feed Heating | Electrical

Rankine Cycle and Regenerative Feed Heating | Electrical4U

Mar 04, 2020· This steam is used to heat the feed water and the device in which it happens is called a feed water heater or a regenerator. Regeneration improves the cycle efficiency by increasing the initial feed water temperature before the water, water enters the boiler and also helps in controlling the large the large flow rate of steam at the turbine exhaust.

Get A Quote

>Objective Questions (Engineering): Thermodynamics (Vapo

Objective Questions (Engineering): Thermodynamics (Vapour

Regenerative heating i.e., bleeding steam to reheat feed water to boiler (a) decreases thermal efficiency of the cycle (b) increases thermal efficiency of the cycle

Get A Quote

>Chapter 8b: Ideal Regenerative Cycles (revised 4/15/1

Chapter 8b: Ideal Regenerative Cycles (revised 4/15/12)

We continue with the Reheat cycle developed in Chapter 8a, and examine the effect of adding a regenerative heat exchanger in the form of an Open Feedwater Heater, as shown below. We will find that this system does result in an increase in thermal efficiency by preheating the water before it enters the boiler, however at the expense of a reduced

Get A Quote

>Analysis Of Steam Cycles - 2 | 10 Questions MCQ Te

Analysis Of Steam Cycles - 2 | 10 Questions MCQ Test

Regenerative heating i.e. bleeding steam to reheat feed water to boiler. A. In regenerative cycle, feed water is heated by. A. exhaust gases. B. heaters. C. steam extraction from the turbine. D. separate boiler. Solution: QUESTION: 8. Reheat cycie in steam power point is used to. A. utilise heat of flue gases. B.

Get A Quote

>PPT – chapter 9 Steam Power Cycle PowerPoint presentati

PPT – chapter 9 Steam Power Cycle PowerPoint presentation

9-4 Regenerative Cycle 9-4-1 Ideal Regenerative Cycle 17 9-4-2 Regenerative Cycle 18 The feed water is heated by steam bleeding out from steam turbine. The average temperature of heat absorption process increases then. 19 1 Steam turbine boiler b a 2 7 condenser 5 6 3 Feed water pump drainage pump Feed water heater 4 20 The more stages of

Get A Quote

Objective ques and ans on thermodynamic cycle-Rankine

>REGENERATIVE RANKINE CYCLE WITH FEEDWATER HEAT

REGENERATIVE RANKINE CYCLE WITH FEEDWATER HEATER

Let if 1 Kg of steam is entering to the turbine from boiler and as we have discussed that certain quantity of the steam will be extracted hence let Y kg of steam is extracted from the turbine at state 5 as shown in figure and therefore (1-Y) kg of steam will be expanded through the turbine up to the condenser pressure.

Get A Quote

>Regenerative feed water heating cycle - LinkedIn SlideSha

Regenerative feed water heating cycle - LinkedIn SlideShare

Sep 01, 2015· The Regenerative Rankine cycle (with minor variants) is commonly used in real power stations. Another variation is where 'bleed steam' from turbine stages is sent to feed-water heaters to preheat the water on its way from the condenser to the boiler.

Get A Quote

>01 regenerative feed heating - slideshare.n

01 regenerative feed heating - slideshare.net

Aug 14, 2014· Regenerative Rankine cycle Another variation is where 'bleed steam' from turbine stages is sent to feed-water heaters to preheat the water on its way from the condenser to the boiler. These heaters do not mix the input steam and condensate, function as an ordinary tubular heat exchanger, and are named "closed feed-water heaters".

Get A Quote

>Regenerative Cycle - an overview | ScienceDirect Topi

Regenerative Cycle - an overview | ScienceDirect Topics

The regenerative cycle is illustrated in Fig. 1.10. Before going to the boiler, the condensate, also known as feed water (FW), after the boiler feed pump (BFP) discharge is heated at various points to avoid irreversible mixing of cold condensate with hot boiler water, which causes loss of cycle efficiency.

Get A Quote
Contact us
Tel

0086-510-68530066

Chat online

Online message


Gas-fired(oil-fired) boilers
Coal-fired boilers
Biomass-fired boilers
Thermal oil heaters
Hot water:0.7-14 MW
14.1-21 MW
21.1-29 MW
29.1-75 MW
Steam :  1-10 t/h
11-20 t/h
21-90 t/h
91-140 t/h