pressure drop from main steam header to turbine inlet

Product thermal capacity: 4-35 t/h
Working pressure: 1.0-2.5 MPA
Outlet temperature:: 184-350 ℃
Available fuel: Bituminous coal, lean coal, anthracite
Available industries: Heating, chemical, food, tobacco, textile, print and dyeing, feed, medicine, building materials, wine, hospital

>CH 1 - CH 3 (Steam Turbines) Flashcards | Quizl

CH 1 - CH 3 (Steam Turbines) Flashcards | Quizlet

In pressure compounded steam turbines: 1. The expansion of steam from boiler pressure to exhaust pressure is carried out in a number of stages 2. Each stage has a set of nozzles and a row of blades 3. All of the velocity available is developed in one set of nozzles 4.

Get A Quote

>Effect of Low Steam Pressure Operation of Boiler - Brig

Effect of Low Steam Pressure Operation of Boiler - Bright

As the main steam pressure drops, there is a good reason for the auxiliary steam pressure to drop. This will depend on many other operating conditions from the turbine and the boiler side. Immediate operator action will depend upon the cause that resulted in the reduction of steam pressure.

Get A Quote

>Types of Steam Turbine - an overview | ScienceDirect Topi

Types of Steam Turbine - an overview | ScienceDirect Topics

To retain the design efficiency the steam inlet pressure should be maintained. Lowering steam inlet pressure reduces turbine efficiency and increases steam consumption. A 10% increase in steam pressure will reduce the steam consumption by about 1% in a condensing steam turbine and by about 4% in a back pressure steam turbine.

Get A Quote

>Pipes and Pipe Sizing | Spirax Sar

Pipes and Pipe Sizing | Spirax Sarco

The ‘pressure loss bar/100 m’ scale reads about 0.9 bar/100 m. The pipe length in the example is 200 m, so the pressure drop is: This pressure drop must be acceptable at the process plant. Using formulae to establish steam flowrate on pressure drop. Empirical formulae exist for those who prefer to use them.

Get A Quote

is the difference between LP, MP, HP and VHP steamSep 22, 2018Why is there tripping in a steam turbine in low vacuumMay 20, 2018What is the minimum pressure required to run a lowMar 16, 2018What is the use of a vacuum in turbine?Dec 04, 2016See more results

How the exhaust pressure for a steam turbine is selecte

What is the difference between LP, MP, HP and VHP steamSep 22, 2018Why is there tripping in a steam turbine in low vacuumMay 20, 2018What is the minimum pressure required to run a lowMar 16, 2018What is the use of a vacuum in turbine?Dec 04, 2016See more results

How the exhaust pressure for a steam turbine is selected?

How exactly the exhaust pressure for a steam turbine is selected. I understand that depending on the turbine size, there is a sweet spot at which the increase in efficiency by lowering the exhaust

Get A Quote

class="b_vList b_divsec">
  • Steam Turbine · Saturated Properties · PRV Calculator · Boiler · Preferences · Flash Tank [PDF]

    Steam Pressure Reduction: Opportunities and Issu

    • Steam Turbine · Saturated Properties · PRV Calculator · Boiler · Preferences · Flash Tank [PDF]

      Steam Pressure Reduction: Opportunities and Issues

      where steam pressure reduction can reduce the operational effectiveness of the steam system. These . areas should be properly accounted for and understood. 5. Steam pressure reduction should be tested to establish the critical minimum pressure at a steam load . that is above average but below peak. This will also provide an estimate of savings. 6.

      Get A Quote
  • >Steam Piping Best Practices | CleanBoiler.o

    Steam Piping Best Practices | CleanBoiler.org

    In order for steam system controls to function properly, they must be installed properly. In the photo to the right, a green-headed PRV (Pressure Reducing Valve) has been installed to reduce the higher pressure steam from the main steam header, to a lower pressure for use in a low pressure application – such as space heating.

    Get A Quote

    >Steam Turbines - MassEngineers.c

    Steam Turbines - MassEngineers.com

    On an impulse turbine, the only time a pressure drop occurs is when steam passes through a nozzle. After steam passes through the nozzles, it passes through the first set of moving blades. In the first set of moving blades, work is extracted from the steam causing the velocity to drop.

    Get A Quote

    >Trap Back Pressure | TLV - A Steam Specialist Compa

    Trap Back Pressure | TLV - A Steam Specialist Company

    The 'back pressure' is the pressure just downstream of the steam trap. In other words, back pressure is the outlet or secondary pressure of the trap. The difference between a trap's inlet (primary) pressure and back pressure is called the 'differential pressure'.

    Get A Quote

    >What are the problems that can occur while running a ste

    What are the problems that can occur while running a steam

    Lower inlet pressure means lower inlet enthalpy. Thus you tend to get lower than predicted power output to a certain pressure provided the steam remains superheated at that pressure. This is why the machine vendors specify a particular range of pr

    Get A Quote

    >Steam Calculators: Steam Turbine Calculat

    Steam Calculators: Steam Turbine Calculator

    Step 1: Determine Inlet Properties Using the Steam Property Calculator, properties are determined using Inlet Pressure and the selected second parameter (Temperature, Specific Enthalpy, Specific Entropy, or Quality). The Specific Enthalpy is then multiplied by the Mass Flow to get the Energy Flow: Pressure = 583.2 psig; Temperature = 485.3 °C

    Get A Quote
    Contact us
    Tel

    0086-510-68530066

    Chat online

    Online message


    Gas-fired(oil-fired) boilers
    Coal-fired boilers
    Biomass-fired boilers
    Thermal oil heaters
    Hot water:0.7-14 MW
    14.1-21 MW
    21.1-29 MW
    29.1-75 MW
    Steam :  1-10 t/h
    11-20 t/h
    21-90 t/h
    91-140 t/h