steam turbine low pressure

Product thermal capacity: 4-35 t/h
Working pressure: 1.0-2.5 MPA
Outlet temperature:: 184-350 ℃
Available fuel: Bituminous coal, lean coal, anthracite
Available industries: Heating, chemical, food, tobacco, textile, print and dyeing, feed, medicine, building materials, wine, hospital

>Utility steam turbines | Steam turbines | U

Utility steam turbines | Steam turbines | USA

Siemens Steam Turbines of the SST-6000 series are widely operated in coal-fired steam power plants with a power output up to 1,200 MW and an efficiency up to more than 46 percent. Products of the SST-6000 series consist of a high-pressure turbine, an intermediate-pressure (IP) turbine, and up to three low-pressure turbines for 50 and 60 Hz.

Get A Quote

>Steam turbine flow & operation | Processing Magazi

Steam turbine flow & operation | Processing Magazine

Steam turbines, especially for small or medium-sized machines, leak steam around blade rows and out the end seals. When an end is at low pressure, as is the case with condensing steam turbines, air can leak into the system. The leakages cause less power to be produced than expected.

Get A Quote

>Mixed-Pressure Turbines | Steam Turbines - Steam Turbin

Mixed-Pressure Turbines | Steam Turbines - Steam Turbines

Mixed-pressure turbines are driven by two different types of steam (high pressure and low pressure) can also be designed for three different types of steam (high pressure, intermediate pressure and low pressure) for power generation. Hence this turbine is most suitable for applications where waste heat is recovered for power generation, such as gas turbine combined-cycle (GTCC) plants, pulp and paper …

Get A Quote

>Low Pressure Steam Turbine Exhaust Flow: Part

Low Pressure Steam Turbine Exhaust Flow: Part 2

Journal of Pressure Vessel Technology; Journal of Solar Energy Engineering; Journal of Thermal Science and Engineering Applications; Journal of Tribology; Journal of Turbomachinery; Journal of Verification, Validation and Uncertainty Quantification; Journal of Vibration and Acoustics; Conference Proceedings. All Conference Proceedings; Browse

Get A Quote

>Low Pressure Steam Turbine Generators | Produc

Low Pressure Steam Turbine Generators | Products

Description: The SST-500 is a single casing, double flow steam turbine with up to 100 MW power output. It can be used as an entire drive or as the low-pressure module of a multiple-casing turboset, directly driven or geared. This turbine, with its capacity to operate over a wide range

Get A Quote

>Why we need intermediate turbine and Low pressure turbi

Why we need intermediate turbine and Low pressure turbine

The exhaust steam from the HP turbine drives the IP turbine, and the exhaust steam from the IP turbine drives the LP turbine. Each expansion stage recovers energy from the steam…

Get A Quote

m Inlet PressureNov 08, 2011Pressurized Steam - an overview | ScienceDirect TopicsJul 04, 2011See more results

LP Turbine - Low-pressure Steam Turbi

Steam Inlet PressureNov 08, 2011Pressurized Steam - an overview | ScienceDirect TopicsJul 04, 2011See more results

LP Turbine - Low-pressure Steam Turbine

In the low-pressure turbine the steam continuously expands from point E to F. The exhausted steam then condenses in the condenser and it is at a pressure well below atmospheric (absolute pressure of 0.008 MPa). The steam is in a partially condensed state (point F), typically of a quality near 90%.

Get A Quote

>High-Pressure Turbine - an overview | ScienceDirect Topi

High-Pressure Turbine - an overview | ScienceDirect Topics

This means that the pressure drop between main steam pressure and first-stage inlet pressure becomes smaller since the control valve opens wider and the pressure drop at the first stage linearly increases.

Get A Quote

>Steam Turbine Basic Parts - Mechanical Engineering Si

Steam Turbine Basic Parts - Mechanical Engineering Site

Feb 11, 2018· Turbine Casings The casing shape and construction details depend on whether it is a High Pressure (HP) or Low Pressure (LP) casings. For low and moderate inlet steam pressure up to 120 bar, a single shell casing is used. With a rise in inlet pressure the casing thickness as to be increasing.

Get A Quote

>Protecting Steam Cycle Components During Low-Lo

Protecting Steam Cycle Components During Low-Load

Feb 28, 2015· Heat-recovery steam generators are optimized for full-power GT operation and often include the ability to add substantial heat via duct burners. At …

Get A Quote

>How do steam turbines work? - Explain that Stu

How do steam turbines work? - Explain that Stuff

Nov 25, 2019· Steam enters from the left through the gray pipe at the top, arriving in the very middle of the turbine and just above it. Then it simultaneously flows in both directions (to the left and the right) through the low-pressure reaction turbine, which drives the electricity generator on the right. Why does steam contain so much energy?

Get A Quote
Contact us
Tel

0086-510-68530066

Chat online

Online message


Gas-fired(oil-fired) boilers
Coal-fired boilers
Biomass-fired boilers
Thermal oil heaters
Hot water:0.7-14 MW
14.1-21 MW
21.1-29 MW
29.1-75 MW
Steam :  1-10 t/h
11-20 t/h
21-90 t/h
91-140 t/h